1/24 scale 2.4g Magracing.

Tips and tricks about building a car. painting it a making it run smooth.
WesR
Posts: 319
Joined: Fri 21. Dec 2012 17:37

Re: 1/24 scale 2.4g Magracing.

Post by WesR » Tue 23. Apr 2019 19:15

I built a 1/24 car last year but somehow it never seemed to go well. Probably I didn't persevere enough as I recently resurrected the car and, with a few mods, I am now quite enjoying it. Certainly the radio gear is much easier to install, as is the CR123 battery and I think that the overall cost could be less than a 1/32 car. Probably with a routed flat pan chassis and 3d printed components. Video hopefully attached. https://youtu.be/QPZCZzSoL1Y

Ned
Posts: 314
Joined: Sun 13. Apr 2014 01:02
Location: Sedona, AZ USA

Re: 1/24 scale 2.4g Magracing.

Post by Ned » Tue 23. Apr 2019 22:24

Wes, your car appears to handle very well. What size magnet did you use in the steering arm to follow the guide wire in the track? Also, what is the diameter of the guide wire in the track?

WesR
Posts: 319
Joined: Fri 21. Dec 2012 17:37

Re: 1/24 scale 2.4g Magracing.

Post by WesR » Wed 24. Apr 2019 18:23

Hi Ned, The guide magnet is a standard 4mm diam. but the steering arm is longer so this, of course, increases the effect.
The wire is 1mm. The track I built last year, after my break from Magracing, had 0.8mm wire. This was ok for 1/32 cars but I struggled with the 1/24 car but I also felt that the track radii were too tight for the bigger car so I built this larger track with larger radii and I played safe by using 1mm wire. My biggest concern with using heavier wire and/or larger magnets is that the cars will not drive across the wire when being driven back onto their lane after an 'off' but this has not proven to be a problem. In fact the 1/32 cars went so well that I lost some interest in 1/24. The building/manufacturing advantages of 1/24 still seem such that I decided to give it another try. This car also goes well as a free running r/c car and this could increase it's sales potential. Not that this compares with Magracing as far as I am concerned but many thousands of 1/24 r/c cars have been sold.

User avatar
davidwp
Posts: 14
Joined: Fri 28. Dec 2012 03:38
Contact:

Re: 1/24 scale 2.4g Magracing.

Post by davidwp » Wed 24. Apr 2019 19:07

Hi Wes,
I now have a place for a track, so I have dragged out my mag steer test car from 2010 (as shown in a previous post above) and want to upgrade it with the latest equipment. Are you willing to share information and pictures of your latest 1:24 chassis, particularly how the front end and steering override are set up?
Thanks, David

User avatar
Keld
Administrator
Posts: 409
Joined: Thu 13. Dec 2012 19:06
Location: Copenhagen, Denmark
Contact:

Re: 1/24 scale 2.4g Magracing.

Post by Keld » Wed 24. Apr 2019 22:10

What electronics do I need to buy if I want to build a 1/24 car, the flysky controller, has it a number?
A receiver for 2.4ghz which’s ?
A part to controls the front wheels.
A list would be nice to have.

I have access to a laser cutter so i can cut parts really precisely

How do you make the steering?
/Keld

WesR
Posts: 319
Joined: Fri 21. Dec 2012 17:37

Re: 1/24 scale 2.4g Magracing.

Post by WesR » Thu 25. Apr 2019 14:15

Good to see the interest in 1/24 cars. The radio you need Keld is Flysky fs-gt2b, as photo. I just googled this and the cheapest came out at £ 18.99 , around 22 euro. on e-bay. This model will include a rechargeable battery in the controller and the standard 2/3 channel receiver. Be sure to get this one, some older versions still need dry batteries. I have 5 of these, all good! All from the far east. About 3 weeks delivery. I usually remove the rx case to reduce the size.

You will also need one micro/mini servo. The size of these is around 21 x 19 x 8mm. The one in my car is by Turningy and these are probably the best, about £6.65 Part no. 144A I think.

There are 2 suitable 2 amp escs (speed controllers) One without brake and one with but I have not managed to get the brake working yet so this is a small problem. I will give more info later, not much time today.


Hopefully I will start soon on 3d printed parts to screw/glue to a flat chassis. A full 3d chassis would be more expensive I think. The car in the photo is a very rough prototype but goes well and I think we would probably go for something of similar layout.
DSCF0847 (2).JPG
DSCF0847 (2).JPG (121.49 KiB) Viewed 210 times
DSCF0844 (2).JPG
DSCF0844 (2).JPG (151.55 KiB) Viewed 210 times

User avatar
davidwp
Posts: 14
Joined: Fri 28. Dec 2012 03:38
Contact:

Re: 1/24 scale 2.4g Magracing.

Post by davidwp » Thu 25. Apr 2019 14:35

"Hopefully I will start soon on 3d printed parts to screw/glue to a flat chassis." WesR

Exactly what i am looking for - hope to see something available soon!

Post Reply