MAGracing Forum

Share your MAGracing with the rest of the world, get inspired and enjoy
It is currently Wed 18. Jul 2018 21:42

All times are UTC




Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6
Author Message
PostPosted: Sun 31. Jan 2016 07:57 
Offline

Joined: Thu 4. Dec 2014 09:53
Posts: 456
Location: cologne
glues everything very good


Top
 Profile  
 
PostPosted: Sun 23. Oct 2016 02:44 
Offline

Joined: Wed 10. Aug 2016 00:44
Posts: 37
Location: Bethlehem, Connecticut USA
Hi, I have questions for rex craemer first,

I've seen the videos of your track and the cars seem to run nicely around it at very good speeds. I am curious about how it was built.

What material is the track and was it routed for the wire?
What size wire did you use and was it coiled or straight pieces?

And questions for anyone else reading this, would anyone recommend using one specific size wire everywhere or mix sizes?

Finally, seeing as .026, .029, .031, .033, .035 diameters are readily available from McMaster Carr and very reasonable in spools, would any of those be suitable and easy enough to use in a routed MDF or plywood track? I guess I'm ready to experiment like everyone else, just looking for suggestions before I do.

Thanks

Brian


Top
 Profile  
 
PostPosted: Sun 23. Oct 2016 04:19 
Offline

Joined: Sun 13. Apr 2014 01:02
Posts: 306
Location: Sedona, AZ USA
I have tried coiled and straight wire. I still have the coiled wire. I strongly recommend straight piano wire, also called music wire. My entire track is made from .032" diameter music wire purchased from ACE Hardware. It's very inexpensive. It's made by K&S Precision Metals in Chicago, stock #501. For this size wire you need a groove in the baseboard about .035" wide and .035" deep. That size groove (slot) is very difficult to make in MDF with a router bit. MDF is very hard causing the bits to break. Plywood would be easier to cut with a router bit. There is no need to use more than one size wire to build a track.

You need to determine how you are going to cut the slot in your baseboard before you purchase your wire. Music wire with a diameter from .028" to .032" should work fine.


Top
 Profile  
 
PostPosted: Sun 3. Jun 2018 19:02 
Offline

Joined: Fri 21. Dec 2012 17:37
Posts: 306
Attachment:
IMG_8895 (640x426).jpg
IMG_8895 (640x426).jpg [ 197.71 KiB | Viewed 151 times ]
Attachment:
Plaster slot track (640x426).jpg
Plaster slot track (640x426).jpg [ 182.27 KiB | Viewed 151 times ]
As most will know, I do of course favour plaster tracks, much to the horror of the slot racing fraternity. I recently came across this slot track (courtesy Pinterest) with wooden slots and some form of plaster/filler surface. It looks pretty good (shame about the slots!) The plaster is 1/4" (6mm) thick so needs 6 times as much plaster as a magracing track! Apparently the builder thinks the rougher surface looks more realistic than smooth board.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group